SawingThe Classic 225 is a manual bandsaw that cuts solid round bar up to 225 mm and squares up to 150 x 300 mm, driven by a 1 HP motor with three blade speeds from 25 to 70 m/min. It runs a 3000 x 27 x 0.9 mm blade through a self-centering vice and German-pattern blade guides for a square, repeatable cut. At about 360 kg it suits small shops and tool rooms that need a dependable, no-frills saw.
SawingThe Classic 300 steps the manual range up to 300 mm round and 300 x 300 mm square capacity on a heavier 600 kg frame. A 2 HP drive turns a 3760 x 27 x 0.9 mm blade at three speeds up to 70 m/min, with a high-efficiency bronze-wheel gearbox and self-centering vice for accurate cuts under heavy daily use. It is built for fabrication shops that have outgrown a smaller manual saw.
SawingThe Swivel 225 is a swing-frame manual bandsaw that cuts straight up to 225 mm round and mitres up to 100 x 100 mm at 45 degrees. It carries the same 1 HP drive, three-speed gearbox and 3000 x 27 x 0.9 mm blade as the Classic 225, with a swivelling head for angled work. It suits workshops that cut frames, brackets and sections needing both straight and mitre cuts.
SawingThe Swivel 300 (Swivel VM 300) is a swing-type manual mitre bandsaw cutting up to 300 mm round, with a 200 x 200 mm capacity at 45 degrees. A 2 HP motor and 3760 x 27 x 0.9 mm blade give it the reach for larger angled work than the Swivel 225. It is aimed at fabrication shops producing structural frames and mitred sections.
SawingThe Steel Master 225 is a rigid manual bandsaw that cuts round stock to 225 mm and squares to 150 x 300 mm, fitted with a 2 HP drive for faster cutting than the Classic 225 at the same capacity. Three blade speeds from 20 to 70 m/min, a self-centering vice and German-pattern blade guides keep cuts square in busy shops. The compact 370 kg frame fits limited floor space.
SawingThe Steel Master 330 is the largest manual saw in the range, cutting up to 330 mm round and 330 x 400 mm square on a 3 HP drive. It runs a heavier 3760 x 34 x 1.1 mm blade at three speeds up to 70 m/min, with a bronze-wheel gearbox and self-centering vice built for heavy daily fabrication. It is a robust choice for high-utilization shops that want manual control at large capacity.
SawingThe Stronger 330 is a double-column semi-automatic bandsaw for straight cutting up to 330 mm round and 330 x 400 mm square, with VFD blade speed from 15 to 80 m/min. A 5 HP drive, hydraulic blade tension and an origin system that returns the head home after each cut give consistent production output. It suits shops moving from manual saws to repeatable semi-automatic cutting.
SawingThe Stronger 430 is a heavy double-column semi-automatic bandsaw cutting up to 430 mm round and 430 x 500 mm square, driven by a 7 HP motor with VFD blade speed from 15 to 80 m/min. Hydraulic clamping and blade tension, a 5300 x 41 x 1.3 mm blade and a 2175 kg frame handle large-section bar and structural steel. It is built for production shops cutting heavy stock day in, day out.
SawingThe MiterSaw 450 is a double-column mitre bandsaw cutting up to 450 mm round and 450 x 600 mm square at 90 degrees, with a precision angle scale for mitres to 45 and 60 degrees. Hydraulic vice clamping, VFD blade speed from 15 to 80 m/min and a 6060 x 37 x 1.1 mm blade give accurate, repeatable angled cuts. It is built for steel service centres and fabricators that mitre structural sections.
SawingThe MiterSaw 3045DS is a double-column double-side mitre bandsaw that swivels both ways for angle cuts on pipe, channel and structural steel. At 90 degrees it cuts 300 mm round and 250 x 450 mm square, with hydraulic clamping and VFD blade speed from 15 to 100 m/min. The double-side swivel suits shops producing mitred frames and trusses that need angles cut left and right without re-fixturing.
SawingThe Compact 150NC is a pivot-type fully-automatic NC bandsaw cutting up to 150 mm round and 150 x 150 mm square, with programmable multiple feed of 300 mm in up to nine increments. NC control, material detection and auto shut-off on blade breakage let it run repeatable unattended cuts on a compact 700 kg frame. It suits job shops that need automated, consistent output without a large machine.
SawingThe HBM 250NC is a pivot-type fully-automatic NC bandsaw cutting up to 250 mm round and 250 x 250 mm square, with VFD blade speed from 15 to 80 m/min and programmable multiple feed of 400 mm in up to nine increments. NC control, helical gear drive, chip brush and material detection support high-throughput unattended runs. It is built for production lines that need automated cutting at mid capacity.
SawingThe MegaX 850x1000CNC is a double-column CNC bandsaw for billet and large-section cutting up to 850 mm round and 850 x 1000 mm square. A 15 HP drive, hydraulic blade tension, programmable saw feed from 1 to 350 mm/min and a smart cutting system with material selection deliver controlled, high-volume cuts behind a CE safety enclosure. It is the flagship of the range for steel mills and heavy fabricators.
SawingThe Verti 14 is a vertical bandsaw with a 350 mm throat and 300 mm work height, driven by a 2 HP motor with VFD blade speed control and a sliding table. The vertical layout suits plate cutting, tool room work and intricate profile cutting where the operator guides the workpiece into the blade. At 320 kg it is the compact entry to the vertical range.
SawingThe Verti 300A is an automatic vertical bandsaw with a servo ball-screw table that feeds work up to 1000 mm wide past the blade for plate and profile cutting. It cuts up to 300 mm high and 400 mm long, with VFD blade speed from 15 to 100 m/min and an origin system that returns the head home after each cut. The servo table on LM guides suits accurate, repeatable plate work.
SawingThe Verti 400A is the larger automatic vertical bandsaw, cutting up to 400 mm high and feeding work up to 1250 mm wide on a servo ball-screw table. A 7.5 HP drive, 5000 x 41 x 1.3 mm blade and VFD speed from 15 to 100 m/min handle heavier plate and section work. The LM-guide table and origin system give repeatable, automated cuts at the top of the vertical range.
SawingThe VM 50 is a cold-cut circular saw for high-speed, clean cuts on tube, pipe and bar stock up to 50 mm. Cold sawing produces a burr-free, square cut face that needs little finishing, making it suited to production cutting where edge quality matters. Full specifications are available on request.
SawingThe VM 80 is a heavy-duty CNC cold-cut circular saw with hydraulic clamping for clean, high-speed cuts on tube, pipe and bar up to 80 mm. Cold sawing leaves a square, burr-free face that reduces secondary finishing in production runs. Full specifications are available on request.
SawingThe VM 100 is a heavy-duty CNC cold-cut circular saw with hydraulic clamping, built for high-speed clean cuts on tube, pipe and bar up to 100 mm. The cold-saw process gives a square, burr-free cut that suits production work needing minimal finishing. Full specifications are available on request.
SawingThe VM 120 is the largest CNC cold-cut circular saw in the range, with hydraulic clamping for clean, high-speed cuts on tube, pipe and bar up to 120 mm. Cold sawing produces a burr-free, square face that keeps secondary finishing to a minimum in production cutting. Full specifications are available on request.
Tell us the product, industry and volume, we'll recommend the right machine and quote it.
Request a Quote